Tips From the Moving Company Pros: Ways To Move a Pinball Maker



With pinball making a substantial renewal across the country, Mild Giant desires to make sure that these traditional, stunning makers stay damage-free while being transferred. Oh, and we desire the individuals moving them to be safe, too.

At first glimpse, pinball devices can appear daunting to move due to the fact that of their size, weight, and fragility. Fortunately, our competent Giants have a couple of techniques up their sleeves to guarantee your pinball is moved with ease.
Folding Down the Headbox

Most of contemporary pinballs (made in the last 20 years or two) have a hinge system which permits the headbox to be folded down. Early pinball makers had their headboxes bolted on, using either two or four bolts. All Electro-Mechanical pinballs utilize this system, in addition to the early Strong State machines.

Later devices have hinges and use a locking system to keep the headbox upright. There might likewise be two bolts inside as added safety, in case the latch is broken or inadvertently un-latched.
Electro-Mechanical Pinballs

For Electro-Mechanical pinball makers, you have to get rid of the headbox rear access panel to access to the bolts and plugs inside. Normally this panel has a lock on it to keep it in location, however with time the secret may have been lost. Frequently, there is a screw keeping this panel in place.

When within, get rid of the bolts and disconnect the large ports that have electrical wiring decreasing into the maker. You might desire to label these connectors to put them back in the right spot, but they must be various sizes, making it tough to plug back improperly.

You can now get rid of the headbox entirely, or fold the headbox down onto the playfield glass. Make sure you use some foam, heavy cardboard, or blankets to protect the headbox from rubbing on the cabinet. Foam is best, as it will help keep the back glass in place.
Early Solid State Pinballs

For early Solid State Pinballs, you will require to eliminate the back glass. There is a lock situated on the headbox in among 3 areas: the left-hand side at the top, right-hand side on top or on top of the headbox in the center.

Once unlocked, remove the back glass by lifting it up using the lift channel (at the bottom of the glass), and after that pull it out from the bottom.

Open up the back box light panel by raising the lock situated on either the left-hand side or right-hand side. The panel can now swing out to you, and offer you access to the circuit boards, plugs, and the bolts. Some Gottlieb pinballs need you to raise the light panel in order to swing it open.

Now that you are within, you can get rid of the bolts, and any plugs that have wires going down into the machine. You may want to label these plugs to put them back in the right spot. You may not need to remove the plugs, as the wiring should be long enough to allow the headbox to be folded down.

At this point, you can lock up the lamp panel and replace the back glass.
Modern Solid State Pinballs

For Data East, Sega, and Stern Modern pinballs, there is a turnable latch system located at the back of the headbox. Using the supplied key, turn the latch 90 ° counter-clockwise.

For Williams, Bally, and Gottlieb, you can easily unlatch the back box at the back of the machine. This is a simple setup and requires no tools.

If you can now fold down the head box onto the cabinet, you're done. Make sure you use some foam, heavy cardboard, or blankets to protect the headbox from rubbing on the cabinet. Foam is best, as it will also help keep the back glass in place.

If you can not fold the head box down, then you have to enter. There is a lock located at the top of the back glass in the. Use the supplied key to unlock, and remove the back glass by raising it up from the bottom, then pulling it out from the bottom.

Next, you will require to get rid of the display screen panel. You can do this by raising it up and out. And lastly, open the light panel. There will be a lock situated on either the left-hand or right-hand side. (Some newer Williams and Bally pinballs do not have a separate amp panel, it belongs to the back glass panel. And later Sega and Stern pinballs use a fluorescent tube for the read this article back glass lighting).

Get rid of the 2 bolts, put the back box back together, and fold down the head box onto the cabinet. Ensure you utilize some foam, heavy cardboard, or blankets to safeguard the headbox from rubbing on the cabinet. Foam is best, as it will also help keep the back glass in place.
Removing the Legs.

Pinball Device legs are held in place by eight bolts. The modern pinballs have captive nuts or threaded plates inside for the bolts to screw into.

These captive nuts and threaded plates can be damaged, and the use of extra nuts might have been needed. If this holds true, you will require to open up the front door of the pinball, slide out the playfield glass, and lift up the playfield.

With the front door (coin door) open, move the lock down bar latch across and get rid of the lock down bar. Move out the playfield glass, and put in a safe place. Next, raise the playfield by placing your hand where the ball drains, and raise the playfield up.

You need to now have access to any nuts that might have been utilized. When any nuts have been removed, change the playfield glass and lock down bar, and lock the front door.

Make certain to mark or keep in mind which legs are for the front and back, as they will be changed differently to suit.
Loading the Pinball.

You are now all set to carry your pinball device. Before you pack it, make sure you remove the pinballs so they do not bounce around throughout transportation.

If you are moving the pinball using a van or SUV, it may be easier to get rid of the legs simply prior to packing the device. Get a good friend to assist and have one of you supporting the pinball, while the other removes the front legs. Move the maker in, and after that eliminate the back legs. It is a lot easier to load the maker front initially.

Make sure you strap the pinball in, as you do not want it moving if you need to stop all of a sudden!

For Electro-Mechanical pinball devices, you need to get rid of the headbox rear gain access to panel to acquire access to the bolts and plugs inside. (Some newer Williams and Bally pinballs do not have a different amp panel, it is part of the back glass panel. And later on Sega and Stern pinballs use a fluorescent tube for the back glass lighting).

If you are moving the pinball using a van or SUV, it might be simpler to remove the legs just prior to filling the device. Grab a friend to assist and have one of you supporting the pinball, while the other removes the front legs.

Leave a Reply

Your email address will not be published. Required fields are marked *